CVE-2026-99751Linux vulnerability
CVE-2026-99751 is a vulnerability in Linux, not yet scored.
Why this priority: Not scored yet, and no exploitation signal.
Published · Updated · NVD status: Received
What it is
The record does not classify the weakness yet; the description below says what the reporter found.
How it is reached
The record does not say yet how the flaw is reached; the description below is the best guide until it is scored.
What an attacker gains
Its impact has not been scored yet.
Is it being exploited?
There is no public report of exploitation yet.
What to do
- Upgrade Linux to a fixed version for your release line (6.12.118, 6.18.64, 7.3.5).
Description from NVD
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix skb_pull() BUG in __bpf_redirect_neigh()
The issue: This is a follow-up to the short link-layer header fixes from Eric. After vlan pop_eth, a privileged SCHED_ACT BPF program can call bpf_skb_change_head(skb, 1, 0) and then bpf_redirect_neigh().
__bpf_redirect_neigh() calls skb_pull(skb, sizeof(*ethh)) after checking only that mac_header < network_header. Nothing verifies that the MAC header is long enough, that it is linear, or that the IP header the redirect goes on to read is linear either.
A SCHED_ACT BPF program can do:
bpf_skb_change_head(skb, 1, 0); bpf_redirect_neigh(lo, NULL, 0, 0);
after vlan pop_eth. The skb then has mac_len == 1 and only one byte of linear data; skb_pull(ETH_HLEN) trips the skb->len < skb->data_len BUG in __skb_pull():
kernel BUG at ./include/linux/skbuff.h:2839! RIP: skb_pull+0x40/0x50 Call Trace: skb_do_redirect -> packet_xmit -> packet_sendmsg Kernel panic - not syncing: Fatal exception in interrupt
The v4 and v6 paths read ip_hdr() and ipv6_hdr() as soon as the MAC header is gone. On the AF_PACKET frame below that leaves headlen == 0 after the pull, so the network header sits at skb->tail and the route lookup reads ip4h->protocol, ip4h->saddr and ip4h->daddr past the linear area.
The Fix: Use skb_network_offset(), which is the MAC header span, instead of skb->mac_len. mac_len is zero for locally generated tc egress and netkit packets, while the span still rejects the one-byte header produced by pop_eth + bpf_skb_change_head(skb, 1, 0). The single check also covers the mac_header >= network_header test it replaces.
Use pskb_may_pull() to make the Ethernet header linear before it is read or pulled, and to make the IP header linear in both the v4 and the v6 path before ip_hdr()/ipv6_hdr() is read. The header pointers are taken after the pull, since pskb_may_pull() may reallocate skb->head.
Conditions to recreate the bug: On x86-64 with 4 KiB pages, enable CONFIG_PACKET, CONFIG_BPF_SYSCALL, CONFIG_NET_SCH_INGRESS, CONFIG_NET_CLS_MATCHALL, CONFIG_NET_ACT_VLAN and CONFIG_NET_ACT_BPF. Run as root with BPF loading, network administration and raw-packet privileges. Bring lo up and attach a SCHED_ACT program that calls bpf_skb_change_head(skb, 1, 0), then returns bpf_redirect_neigh(skb->ifindex, NULL, 0, 0):
ip link set lo up tc qdisc add dev lo clsact tc filter add dev lo egress matchall action vlan pop_eth pipe \ action bpf object-file neigh_chghead.o section action
Send an untagged ETH_P_IP frame of ETH_HLEN + 8192 bytes through an AF_PACKET/SOCK_RAW socket bound to lo, without PACKET_VNET_HDR or PACKET_QDISC_BYPASS. Use a unicast destination MAC. The sender's skb has a 14-byte linear Ethernet prefix and a fragmented payload; pop_eth removes that prefix and change_head restores only one linear byte. The unfixed neighbor redirect then tries to pull 14 bytes and BUGs.
Sending the same frame without pop_eth and change_head leaves the IP header in the frags, which is the route lookup reading past skb->tail.
What this means for your architecture.
A CVE names a product. Whether it matters depends on where that product sits in your systems: what reaches it, which trust boundary it guards and what it can reach once compromised. Veriom maps your components, their relationships and your trust boundaries from your code, cloud and delivery evidence, so you can see where a component like this sits. The radar itself does not look at your systems.
Components it touches
- Linux. Start from where it runs and what it is connected to.
Trust boundaries in play
Questions to answer about your own systems
- Where does Linux run in your systems, and at which version?
- Which of those instances are reachable by people you do not trust?
- What can it reach once compromised: which data stores, secrets and services?
14-day free trial
Understand how your systems connect.
See your services, dependencies and trust boundaries in one place, with evidence from your connected environment.
Sources
- CVE records and CVSS scores from the NVD CVE API. This product uses the NVD API but is not endorsed or certified by the NVD.
- Exploitation status from CISA’s Known Exploited Vulnerabilities catalog.
- Exploit likelihood from FIRST’s Exploit Prediction Scoring System (EPSS), refreshed daily.
- Explanations are written by Veriom from fixed templates over each record’s data, not by a person reviewing each CVE. Descriptions are quoted from the records as published.